PROJECT 12 - CATIA V5 - BASE BRACKET DESIGN

Aim: To Creation of CAD model considering Class A surface, Nominal thickness and Attachment strategy.   Objective: To Creation of CAD model considering Class A surface, Nominal thickness and Attachment strategy. Create thickened part using master section for reference Create the mounting features as per design guidelines…

HOOD DESIGN OF A CAR AIM : To design the hood of a car with the given input Outer panel and its dimensions.   Hood Introduction :   The hood (North American English) or bonnet (Commonwealth English) is the hinged cove over the engine of motor vehicles. Hoods can open to allow access to the engine compartment…

BUMPER DESIGN AIM: to make a model from the provided class-A surface.INTRODUCTION:CLASS-A SURFACE: a surface made by the designer which is given as an input to the plastic modeler to work on. It is aesthetic surfaceand the outer most surface.CLASS-B SURFACE: a surface below a certain thickness from the class-A…

AIMIn this week’s assignment, you will have to create 2 assemblies according to the contentcovered in the course videos. You will be provided with 2D diagrams of the componentsand you will have to first create the individual part files and then create a completeassembly of those part files in the assembly workbench.…

A PILLAR DESIGN WITH MASTER SECTION MASTER SECTIION                    REFERENCE FOR CLASS A, CLASS B & CLASS C SURFACE.     CLASS A SURFACE                  check the surface quality  CLASS A SURFACE  …

Aim:To Create a DRILL HANDLE attach with B side features Ribs & screwboss plastic component design throught the given CAT Part file from Class A surface Tomake a Class B & Class C Surface and final component. Used viaCatia V5 software- tools used given below,Point through on the center of the surfaceAxis creationLine…

Week 8 - Challenge 4 - Coin Holder DESIGN OF COIN HOLDER AIM: To create the coin holder plastic component through the given Class A surface. Tobegin with the tooling axis for the given Class-A surface should be created meeting therequirements of the draft angle and at the end perform the draft analysis on the model.Take…

AIM:to create the core and cavity for the switch bezel condering the all design rules. TOOLING AXIS: IT IS THE AXIS IN WHICH THE DIRECTION CORE AND CAVITY OPEN. THIS IS THE VERY IMPORTANTFOR PRODUCTION OF PLASTIC COMPONENT. MOST OF THE DEFECT WILL DONE IMPROPERTOOLING AXIS CREATION BY THE PLASTI DESIGNER.THERE ARE SO MANY…

Week 8 - Challenge 2 - Switch Bezel Design Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Take the Thickness…

Week 8 - Challenge 1 - Base Bracket Design   Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. NOTE: Tree Structure…

What is Underbody Coating?    Underbody coating is a thick cladding (typically made of rubber) that is placed uniformly to the car’s underside. When the automobile is fresh off the lot and spotless, it is usually sprayed or painted on. But it’s acceptable if you apply the undercoating after a couple…

BENCHMARKING 1: Mr. D.S. Pughazhyendhii's family requires what Safe Car yet the value which offers an Equilibrium strike of Mileage, Maintenance with Good space, Features and a Social Status too of not to be owning a car which is of entry segment but one which offers Value. With Transformation happening in Mindsets - Safety…

DOOR TRIM LOWER Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class A surface and Solid model…

Dog house design for the Door Trim:Aim: Create the Dog House for the Door Trim considering the design rules and performthe draft analysis for class A and create the final close body component and performthe draft analysis.Objective:Create the Tooling axis Design the class-B and class-C surfaces and join them.Use the Close…

Project 2: Deals with the development of a forward energy-based fuel consumption model of a Hybrid Electric Vehicle.   Task: The task of this project is to quantify the improvement in fuel economy numbers for the hybrid vehicle (kmpl), compared to the conventional vehicle, on the urban cycle (UDDS) and highway cycle…

Project 1: Deals with the development of a forward energy-based fuel consumption model of a conventional vehicle.   Aim:- 1] Build Simulink model using blocks and complete the vehicle model. 2] Witting scripts in MATLAB to load all the variables required for running the Simulink model. 3] tabulate the fuel economy…

AIM :  To study system-level simulation of an all-terrain vehicle and explain the results.           OBJECTIVE: Generate a Simulink model various graphs for different input vs output ration   Results & generate reports.    SOLUTION:  All-Terrain Vehicle…

AIM - Program in Matlab to simulate the forward kinematics of a 2R Robotic Arm OBJECTIVE - Program in Matlab to simulate the forward kinematics of a 2R Robotic Arm PROCEDURE - The robotic arm is a mechanical arm us for different industrial operations. And it’s a programmable. The robotic arm is mainly consists with…

   AIM:  Make a Mat Lab code to solve and generate plot for Simple Pendulum.  OBJECTIVE:                      Make a Mat Lab code to solve and generate plot for Simple Pendulum. The code should create…

 AIM:  Make a Mat Lab code to solve anonymous function stalagmite with Genetic Algorithm and generate plot with finding global maxima.                     OBJECTIVE:                …

 AIM:  Create the Rankine Cycle Simulator using MATLAB.                                           OBJECTIVE:          …

AIM: Make a Mat Lab code to calculate thermodynamic properties of various gas species &   file parse of NASA thermodynamics data.  OBJECTIVE:                     Making the function to calculate the enthalpy,…

AIM:  SIMULINK MODEL FOR DOORBELL & THERMISTOR.                     OBJECTIVE:      1.  To make Simulink model for a doorbell using solenoid block.      2.  To use thermistor to sense temperature of a heater and turn…

AIM  :  To implement control logic of a “washing machine” using State flow as per the inputs provided in power & water supply. Make a Simulink chart for the “Gear shift” logic. Give speed input while the simulation is running & display the gear number.             …