Week 12 - Project-1
Aim : Follow the Quality Criteria and mesh the following component and assign thickness: Target Element Length = 4mm S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2mm 6 Max. Length 6mm 7 Min angle Quad 45 8 Max angle Quad 135 9 Min…
abhijeet dhillon
updated on 12 Oct 2020
Aim :
Follow the Quality Criteria and mesh the following component and assign thickness:
Target Element Length = 4mm
| S.N | Quality Criteria | Value |
| 1 | Aspect Ratio | 5 |
| 2 | Skewness | 45 |
| 3 | Warping | 15 |
| 4 | Taper | 0.5 |
| 5 | Min. Length | 2mm |
| 6 | Max. Length | 6mm |
| 7 | Min angle Quad | 45 |
| 8 | Max angle Quad | 135 |
| 9 | Min angle Tria | 20 |
| 10 | Max angle Tria | 120 |
| 10 | Tria % | 10 |
Solution:
Using the surface trim command we have trimmed the component vertically as shown below :
Creating the horizontal trim we get :
Creating new component as shown below which divides the the door into 4 sub components :
Using the defeature command we have removed the fillets as shown below :
Using surface offset we have created a mid surface of this section :
Meshing it gives :
Part 2 :
Defeaturing Fillets :
After using the commands such extend and defeature and do the meshing we get the following :
Part 3 :
Creating the midsurface of the base we get :
We will defeature the following ribs :
As you can see they have been defeatured and mid surfaced :
Now the defeaturing has been done :
Part 4 :
After midsurfacing and defeaturing we get :
Quality Check :
Conclusion :
The above part has been meshed as shown below :
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by abhijeet dhillon (77)
Week 2 Air standard Cycle
Aim : Your code should create a PV diagram Your should output the thermal efficiency of the engine. Solution : The code for the PV diagram is as follows : import math import matplotlib.pyplot as plt #inputs p1=101325 t1=500 gamma=1.4 t3=2300 #Geometric dimensions : bore=0.1 stroke=0.1 con_rod=0.15…
18 Jun 2022 12:07 PM IST
Bird Strike - Project - 2
Aim : The final submission must include the input file, animation, and a report. - Since this is a quite difficult and involved project, students are advised to log their debugging process and include it in the report. The log is a description of the solution process and challenges encountered along the way. …
17 Apr 2022 05:21 AM IST
Week 1 Understanding Different Battery Chemistry
Aim : 1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it 2.Compare the differences between each type of Li+ion batteries based on their characteristics Solution :…
08 Mar 2022 03:21 PM IST
Week - 10 Hyperelastic Material Models
Aim : Given the material data below, calculate the Mooney Rivlin and Ogden material constants and compare the both using stress-strain data from a Dogbone specimen tensile test with 100 percent strain. The given data is the engineering stress-strain in MPa/(mm/mm). The comparison should be shown from the d3hsp file and…
27 Feb 2022 05:08 AM IST
Related Courses
0 Hours of Content
