Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo

Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo

WEEK-10 CHALLENGE

N.KEERTHANA

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.

   AIM :- To create a set of sinusoidal points, create a curve and to create a surface out of the curve

   PROCEDURE :-

   Step-1:- 

• Open the Revit software and goto manage tab and click on the Dynamo tool
• In the dynamo, double click on the dynamo screen, the code block will appear
• Create three code boxes in dynamo screen and give the appropriate names as start, end and step
• Next insert the range and connect start to start, end to end and step to step
• Then type the points by coordinates and connect the sequence to the x coordinate 

   Step-2:-

• Type math.sin and connect the range seq to the angle
• Then type product connect sin to the x
• Next, type code block and rename it as amplifier and connect it to y of the product
• Type add and insert it and connect var of product to the x of add
• Connect var of add to the y of the point by coordinates
• Then, we type integer slider and give the minimum integer value as 20 and connect it to the degree of y of add
• Type nurbscurve coordinate and insert it
• Then, connect the point of point by coordinates to the point of nurbscurve coordinates
• Later, type integer slider and give the minimum integer value as 5, and connect it to the degree of nurbscurve by control points

   Step-3:-

• Copy the total group and paste it for four times
• Type list.create and insert and create a four items in the list.create
• Then connect nurbscurve of all 4 groups to the 4 items in the list.create 
• Then type surface by loft and connect the list to cross section surface
• Finally the surface has been created

2) Create a conceptual layout of floor plan in dynamo . Using the tools available in dynamo link the lines to appropriate model elements in Revit by choosing the wall types and wall parameters. Make use of the sliders to slide through the height of the wall and length of the wall.

 AIM:- To create a conceptual layout of floor plan in dynamo using the tools available in dynamo link

 PROCEDURE:-

 Step-1:-

• First, we have to enter two integer slides and name them as x and y and give the minimum integer value as 100
• Then type point by coordinates four times
• Connect created integer sliders to the point by coordinates
• Type line.ByStartPointEndPoint and create it four times
• Connect point bycoordinates to the line.ByStartPointEndPoint
• Next, the remaining members are created by coordinate points
• Then, the rectangle is created by coordinate points

 Step-2:-

• Minimize the dynamo screen, and the revit software appears
• Then the conceptual layout plan is created

 Step-3:-

• Then, we adjust the height of the wall using the integer slider 
• Also we can change the minimum and maximum value of the wall height 

  Step-4:-

• Next we select the global parameters and give the value as 50'
• Then, the length of the wall will be changed

3) Create an array of model elements in Revit. Use dynamo to vary the properties of model elements by using the slider or code block

  AIM:- To create an array of model elements in revit using dynamo to vary the properties of model elements by using the slider or code block

  PROCEDURE:-

• Open the Revit software using the architectural template
• Create nine columns
• Open the Dynamo tool and then the dynamo will be opened
• we type select model elements, integer slider and familyinstance.SetRotation
• Connect elements of select model elements to the familyinstance of familyinstance.SetRotation
• Then, connect integer slider to the degree of familyinstance.SetRotation
• The columns are rotated to the 45 degrees

4) Create a conceptual mass in Revit and develop a parametric column by dividing the surfaces and apply the concepts similar to used in parametric walkway modelling. Use triangular bent or square shaped panels to add finish to the parametric column

 AIM:- To create a conceptual mass in revit and develop a parametric column by dividing the surfaces and to apply the concepts similar to used in parametric walkway modeling

 PROCEDURE:-

• We open the Revit software and select the new option in the family
• The new family tab will be visible, select the mass in the conceptual mass folder 
• After selecting the mass from the conceptual mass folder, the new screen will be visible
• Then, we open the north elevation and need to create the level-2
• We use the spline tool to draw the walkway curve
• At the control points, we have to create the workplane and draw the polygon with four sides to the workplane
• Similarly create workplane at the control points and draw the polygon with four sides in different angles
• Select the curve line, control points, workplane and polygon then, create foam
• We open the new family and select the metric curtain panel pattern based
• Then select the triangle bent pattern
• Create the plane at the midpoint and also place the circle at the midpoint with diameter of 2"
• Then, the triangle bent pattern was created and then click on the 'load into project' option
• The triangle bent pattern will be loaded into the project
• We apply the triangle bent pattern to the parametric column