Hyundai Venue S Engine and Transmission Engine Type 1.2 Kappa Petrol Engine Displacement 1197 cc Max Torque …
Thirumal Reddy Murugesan
updated on 23 Dec 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Thirumal Reddy Murugesan (20)
Project 2
Objective:To route the Wiring harness on the given car body and Prepare flatten view drawing in CATIA V5.Process:Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system…
10 Feb 2023 03:26 PM IST
Hood design-Week 2
AUTOMOBILE HOOD DESIGN: Here we are going to understand and design the concept of front-mounted engine’s hood according to the standards. The hood or bonnet is the hinged cover over the engine of motor vehicles that allows access to the engine compartment, or trunk for maintenance…
25 Jan 2023 05:35 PM IST
Underbody Coating
UNDER BODY COATING : Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…
23 Dec 2022 09:25 AM IST
Benchmarking
Hyundai Venue S Engine and Transmission Engine Type 1.2 Kappa Petrol Engine Displacement 1197 cc Max Torque …
23 Dec 2022 08:33 AM IST
Project 1
Objective: To route the Wiring harness on the given Engine and Prepare flatten view drawing in CATIA V5. Process: Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system definition.…
03 Dec 2022 01:43 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
Objective: Flatten the harness assembly completed in the "week 4 challenge". • Place the flattened view on the drawing sheet. • Ensure bundles with protective coverings has different visuals on the drawing view. Process: Defining the cad files: Open the igs…
17 Nov 2022 06:20 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
Objective: To route harness layout in Electrical workbench. Process: Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system definition. Make sure the x-axis is pointing…
14 Nov 2022 05:39 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Objective: To route the harness layout in the Electrical workbench using the connectors, •DT06-4S • DT06-6S .DT06-2S • DT06-08SA Add protective covering on all branches connected to DT06-2S & DT06-4S connectors and keep the end extremity at 30mm. Process: DT06-4S: • Open the DT06-4S igs file and create a midpoint on the…
11 Nov 2022 05:00 PM IST
Wiring harness routing & packaging Rules Week 3 Challenge
Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Objective: To define clip cad as electrical support using electrical part design workbench. Process: First, we have to define the geometry parameters of the P clamp. We need to…
09 Nov 2022 03:16 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge
Objective : To define connectors & Connector clip cad as Electrical connectors using Electrical Part design Workbench. 1. Deutsch DT06 – 08SA : Process: Open the Deutsch DT06 – 08SA igs file and create a midpoint on the face using point type as between. Now we can create an axis system to the…
08 Nov 2022 01:17 PM IST
Week 10- Assembly Workbench
AIM: To create the 3D Part from the 2D Sketch and Assembly in Assembly Part Design. OBJECTIVE: To create the Solid part from the 2D Sketch. All Sketch must should in positioned sketch and also Iso-Constraine. Ensure Created parts arein Same Folder. Ensure all assembly are corrected and constrained.…
06 Nov 2022 05:21 PM IST
Week 9 - Project - A pillar Design with Master Section
A Pillar Ramakrishnan Safran SL, [06-Nov-2022 at 10:27:54 PM]: AIM: To craete the Solid part from the given Class A surface and Follow the Master section for B Side Feature to creation. OBJECTIVE: Picture of the sketches with Sketch solving status’s geometry…
06 Nov 2022 05:08 PM IST
Week 9 - Project 1 - Door Trim Lower with Engineering Features
1. A detailed report should be done explaining the draft analysis at the Class A surface. Draft analysis on Class A surface of Door trim Lower -Step 1- Open draft analysis and move the compass to coincide with the Tooling axis Step 2- Lock the compass and check the radius/angles using the running analysis…
17 Oct 2022 01:03 PM IST
Week 9 - Attachment Feature Creation - Challenge 2
Tooling Axis creation: Using the tooling axis created along the x and y-axis, these tooling axes are used to create the tooling axis by a bisecting method where the two lines and points will be selected as inputs. Draft Analysis: The Draft Analysis command lets you detect if the part you drafted will be easily removed.…
26 Sep 2022 03:32 PM IST
Week 9 - Attachment Feature Creation (Ribs & Screw Boss) - Challenge 1
Tooling Axis creation: Using the tooling axis created along the x and y-axis, these tooling axes are used to create the tooling axis by a bisecting method where the two lines and points will be selected as inputs. Draft Analysis: The Draft Analysis command lets you detect if the part you drafted will be easily removed.…
26 Sep 2022 03:18 PM IST
Week 8 - Challenge 6 - Core & Cavity Design
1.A detailed report should be done explaining the draft analysis and the tooling axis creation. Draft analysis on Class A surface of Switch Bezel below-Step 1- Open draft analysis and move the compass to coincide with Tooling axis as below Step 2- Lock the compass and check the radius using the running analysis option-…
24 Sep 2022 08:44 PM IST
Week 8 - Challenge 4 - Bumper
1. A detailed report should be done explaining the draft analysis at the Class A surface. Draft analysis on Class A surface of Bumper-Step 1- Open draft analysis and move the compass to coincide with the Tooling axis Step 2- Lock the compass and check the radius/angles using the running analysis…
23 Sep 2022 08:59 PM IST
Week 8 - Challenge 3 - Coin Holder Design
1. A detailed report should be done explaining the draft analysis at the Class A surface. Draft analysis on Class A surface of Coin holder-Step 1- Open draft analysis and move the compass to coincide with the Tooling axis Step 2- Lock the compass and check the radius/angles using the running analysis…
22 Sep 2022 07:27 AM IST
Week 8 - Challenge 2 - Switch Bezel Design
1.A detailed report should be done explaining the draft analysis and the tooling axis creation. Draft analysis on Class A surface of Switch Bezel below-Step 1- Open draft analysis and move the compass to coincide with Tooling axis as below Step 2- Lock the compass and check the radius using the running analysis option-…
18 Sep 2022 06:58 PM IST
Week 8 - Challenge 1 - Base Bracket Design
BASE BRACKET
16 Sep 2022 04:56 PM IST